Skip to main content

HELLO THERE!!!!



     Well, this is my first post in here. About me a little bit would suffice as an introduction. I am Halim, Malaysian, in early 20's, engineering student. My hobbies ranging from tinkering with arduino stuffs to making flowers using beads. Well, I suppose i could share some of my writings here also. I also have an instructables page where I share my Arduino tinkering projects over yonder. I am planning to share tutorials about my hobbies and my tinkerings in this blog and I hope anybody reading the blog could get benefits from it. Well, I think that's good enough as an introductory post. Oh, wait!! I'll give you links for my instructables experiments:


1.http://www.instructables.com/id/Experiment-for-Fun-Morse-Code-Encrypter-Using-Ardu/
2.http://www.instructables.com/id/Arduino-MIT-App-Inventor-Servo-Motor-Controller/
3.http://www.instructables.com/id/Controlling-Servo-motor-using-Keyboard-input/
4.http://www.instructables.com/id/Hello-world-of-Parallel-programming-in-Ubuntu-with/

5.http://www.instructables.com/id/Custom-Music-Maker/

6.http://www.instructables.com/id/Control-Your-Multicolor-LED-Using-Smartphone/

Comments

Post a Comment

Popular posts from this blog

Arduino and Multi Function Shield: Pots,LEDs and buzzers

HELLO THERE!!!!!    How are you guys? I hope everyone is fine and in good mood always. This week, I continue my tinkerings with the Multi Function Shield. In this experiment, I used the potentiometer in the shield to control the LEDs in the shield. Without further wasting time, let's jump in straight to the experiment!! HARDWARE 1.ARDUINO UNO  2.MULTI-FUNCTION SHIELD SOFTWARE: 1. ARDUINO IDE CIRCUIT ASSEMBLY    The circuit assembly is fairly simple. Just attach the multi function shield on top of Arduino properly. Please attach the shield properly as failure to do so would cause the shield  not to function as intended. CODING THE ARDUINO: Let's refer to the multi-function shield image below: Referring to the image of the shield, it can be seen that the potentiometer (blue object near buttons) is connected to pin A0 (analog 0)     int pot = A0; //declaring the pot ...
Post a Comment
Read more

Arduino Beginner Experiments: Arduino and Light Blocking Sensor

HELLO THERE!!!     How are you guys? I hope everyone is fine and in a good mood always. This week, I would like to share with you guys my experiment on Arduino and Light Blocking Sensor. The objective of this experiment is to receive feedback from the sensor ( Digital and Analog) What is Light Blocking Sensor?      A linear hall sensor is a type of sensor which responds when the sensor is blocked out from light. The sensor is different for LDR's as LDR's responds to the amount of light it received while the light blocking sensor responds if the light is blocked out or not from the sensor.It can be used for both digital and analog measurements. HARDWARE: 1.Arduino UNO 2. Light Blocking Sensor SOFTWARE: 1.Arduino IDE CIRCUIT ASSEMBLY   Let's refer to the image of the blocking sensor below: The Connection of the Sensor to the Arduino is shown below: SENSOR  ----->       ARDUINO Signal   ...
Post a Comment
Read more

Arduino and Keyes KY-017 Mercury Tilt Sensor

HELLO THERE!!!     How are you guys? I hope everyone is fine and good as always. I am back in tinkering after a few months of hiatus( busy stuff :) ). So, today i would like to share with you guys on KY-017, which is a Keyes Mercury Tilt Sensor. KY-017 Sensor KY-017      The picture above shows the KY-017 Sensor from Keyes. It has 3 pins, A ground, A vcc, and A signal pin. If you look closely, there is a mercury ball inside the bulb like object. The mercury ball acts like a switch for this sensor. KY-017 Working Procedure: 1. When the sensor is not tilted, the mercury ball will be at the bottom of the bulb. This will complete the circuit and turns on the LED of the sensor. The output that is sent through the signal pin will be LOW. 2.When the sensor is tilted, the mercury ball will be at the top of the bulb(near at the sharper end). This will complete break circuit and turns off the LED of the sensor. The output that is sent through t...
Post a Comment
Read more