Skip to main content

Arduino and Multi Function Shield: Pots,LEDs and buzzers

HELLO THERE!!!!!


   How are you guys? I hope everyone is fine and in good mood always. This week, I continue my tinkerings with the Multi Function Shield. In this experiment, I used the potentiometer in the shield to control the LEDs in the shield. Without further wasting time, let's jump in straight to the experiment!!


HARDWARE
1.ARDUINO UNO
 2.MULTI-FUNCTION SHIELD





SOFTWARE:
1. ARDUINO IDE


CIRCUIT ASSEMBLY

   The circuit assembly is fairly simple. Just attach the multi function shield on top of Arduino properly. Please attach the shield properly as failure to do so would cause the shield  not to function as intended.





CODING THE ARDUINO:

Let's refer to the multi-function shield image below:




Referring to the image of the shield, it can be seen that the potentiometer (blue object near buttons) is connected to pin A0 (analog 0) 
  

int pot = A0; //declaring the pot and led pins
int l1 = 13;
int l2 = 12;
int l3 = 11;
int l4 = 10;
int val;//initializing variable called val


void setup()
{
  Serial.begin(9600);//serial communication is set at 9600 bps
  pinMode (l1,OUTPUT);//setting all the leds as an output
  pinMode (l2,OUTPUT);
  pinMode (l3,OUTPUT);
  pinMode (l4,OUTPUT);
}
 void loop()
 {
  val = analogRead(pot);//read the pot value and keep in variable called val
  Serial.println(val);//print out the val value(pot value)
  
  if ( val <= 200)//if val(pot value) is less than 200, then, do the following
  {
    digitalWrite(l1,LOW);//turn off the led
    digitalWrite(l2,HIGH);//turn on the led
    digitalWrite(l3,HIGH);
    digitalWrite(l4,HIGH);
  }
   if ( val <= 400 && val > 200)
  {
    digitalWrite(l1,LOW);
    digitalWrite(l2,LOW);
    digitalWrite(l3,HIGH);
    digitalWrite(l4,HIGH);
  }
   if ( val <= 600 && val > 400)
  {
    digitalWrite(l1,LOW);
    digitalWrite(l2,LOW);
    digitalWrite(l3,LOW);
    digitalWrite(l4,HIGH);
  }
   if ( val > 600)
  {
    digitalWrite(l1,LOW);
    digitalWrite(l2,LOW);
    digitalWrite(l3,LOW);
    digitalWrite(l4,LOW);
  }
 }


Upload the code to your arduino and see the results!! You can turn the knob (yellow screw on top of the pot) to adjust the value and see how many led's light up depending the pot value!!


You can also use the same trick on buzzer on the shield. From the shield image above, you can see that the buzzer is connected to digital pin 3. 

if you want to use buzzer:

While initializing:
int Buzz = 3;


In void setup:
pinMode(Buzz, OUTPUT);

In void loop:
tone(Buzz,val,2000); //Working but not as intended(the duration val,2000, not working)
or
digitalWrite(Buzz,HIGH/LOW);//simply turn on or turn off the buzzer



Well, that's all from me for this week guys, hope to see you guys next week.Till then HAPPY TINKERING!!!

Comments

Popular posts from this blog

Arduino Beginner Experiments: Arduino and Light Blocking Sensor

HELLO THERE!!!     How are you guys? I hope everyone is fine and in a good mood always. This week, I would like to share with you guys my experiment on Arduino and Light Blocking Sensor. The objective of this experiment is to receive feedback from the sensor ( Digital and Analog) What is Light Blocking Sensor?      A linear hall sensor is a type of sensor which responds when the sensor is blocked out from light. The sensor is different for LDR's as LDR's responds to the amount of light it received while the light blocking sensor responds if the light is blocked out or not from the sensor.It can be used for both digital and analog measurements. HARDWARE: 1.Arduino UNO 2. Light Blocking Sensor SOFTWARE: 1.Arduino IDE CIRCUIT ASSEMBLY   Let's refer to the image of the blocking sensor below: The Connection of the Sensor to the Arduino is shown below: SENSOR  ----->       ARDUINO Signal      ------>     Any Analog/Digital pin

Arduino Tinkering : Controlling multiple LED with multiple potentiometers

HELLO THERE!!!!            How are you guys? I hope everyone is fine and well always. For this week's post, I would like to share with you guys a simple tinkering on Arduino, LED, and potentiometers. The objective of the experiment is to light up different amount of LED's with different intensity by controlling two potentiometers. Before starting, of course, we need to know what items are needed. The items needed are: 1. Arduino UNO   2. 4 to 5 LEDs 3. 2 Potentiometers The software used in this experiment is: 1. Arduino IDE. Now that all the hardware and software are obtained, let's go to the schematics of the circuit. The circuit is quite simple actually. The long legs of the LED's were connected to PWM pins while the shorter legs were connected to ground. The potentiometers however have three legs. The middle leg is connected to the analog pins (A0, A1) while the other two legs were connected to 5V and GND respectively. Don't w