Skip to main content

Arduino Beginner Experiments: Reading the DHT11 Data in Smartphone

HELLO THERE!!!

        How are you guys? I hope everyone is fine and in a good mood always. In this post, I would like to share with you guys an experiment which is the continuation of last post experiment. In this experiment, I would like to read the DHT 11 sensor values in my smartphone. So, I would like to share two ways to do so.


HARDWARE:
1.Arduino UNO
2. Bluetooth Module (I used HC-06 )

3. DHT11 Sensor (If you are using LM35 refer here:  http://halim930112.blogspot.my/2016/04/arduino-experiments-lm35-and-graph.html)

4. Smartphone
SOFTWARE:
1. MIT App Inventor 2
2. Bluetooth Terminal (Downloadable from Play Store)


CIRCUIT ASSEMBLY:



 Referring to both of the Images above, the connection is as follows:

HC-06                                    Arduino
--------                                    ----------
RX      ----------------------->  TX
TX      ------------------------> RX
GND  -------------------------> GND
VCC  --------------------------> 5V



DHT11                                    Arduino
---------                                    ----------
S          ------------------------>  Any Digital Pin
Middle Pin --------------------> 5V
-            ------------------------> GND


CODING THE ARDUINO:

We can use the same code used in last post. The code in the last post is here ( http://halim930112.blogspot.my/2016/12/arduino-beginner-experiments-measuring.html )


After writing the code, upload the code to your Arduino. To view the readings of the sensor in your smartphone, there are two ways. The first way (the easiest way) is to download the bluetooth terminal app in the playstore. There are few of those software online ( I am using the Bluetooth Terminal). After downloading the software, we can try to connect the our phone with the Arduino and view the readings. Below are the steps I used to setup my app with Arduino.



This is the main screen (GUI) of the Bluetooth Terminal App. Click on 3 dots on the top right of the app to open a list of drop down menu.

Select the Connect a device- Secure option. Then, a pop up will appear listing all of the connectable bluetooth items
After successful connection, the data from the Arduino will be transmitted to your smartphone






    The second way is to build an android app using the MIT App Inventor 2. This app that I am going to show you will do 2 things:

1. Show the reading of the DHT11 in your phone.
2. Log the readings in a text file

 The MIT App Inventor UI and block codes are as shown below:

The Main Screen (the GUI)

The Block of codes used for this App

After creating the App, install it in your smartphone. If you run the app, the app will automatically log the data received in a text file. Example of the text file is shown below:

Readings from the DHT11





If you want to try out the app, you can download it from here (ai2.appinventor.mit.edu/?galleryId=6198770507972608).Well, that's all from me this week, folks. I hope to see you guys in the next post. Till then, I would like to say HAPPY TINKERING!!!!













Comments

Post a Comment

Popular posts from this blog

Arduino and Multi Function Shield: Pots,LEDs and buzzers

HELLO THERE!!!!!    How are you guys? I hope everyone is fine and in good mood always. This week, I continue my tinkerings with the Multi Function Shield. In this experiment, I used the potentiometer in the shield to control the LEDs in the shield. Without further wasting time, let's jump in straight to the experiment!! HARDWARE 1.ARDUINO UNO  2.MULTI-FUNCTION SHIELD SOFTWARE: 1. ARDUINO IDE CIRCUIT ASSEMBLY    The circuit assembly is fairly simple. Just attach the multi function shield on top of Arduino properly. Please attach the shield properly as failure to do so would cause the shield  not to function as intended. CODING THE ARDUINO: Let's refer to the multi-function shield image below: Referring to the image of the shield, it can be seen that the potentiometer (blue object near buttons) is connected to pin A0 (analog 0)     int pot = A0; //declaring the pot ...
Post a Comment
Read more

Arduino Beginner Experiments: Arduino and Light Blocking Sensor

HELLO THERE!!!     How are you guys? I hope everyone is fine and in a good mood always. This week, I would like to share with you guys my experiment on Arduino and Light Blocking Sensor. The objective of this experiment is to receive feedback from the sensor ( Digital and Analog) What is Light Blocking Sensor?      A linear hall sensor is a type of sensor which responds when the sensor is blocked out from light. The sensor is different for LDR's as LDR's responds to the amount of light it received while the light blocking sensor responds if the light is blocked out or not from the sensor.It can be used for both digital and analog measurements. HARDWARE: 1.Arduino UNO 2. Light Blocking Sensor SOFTWARE: 1.Arduino IDE CIRCUIT ASSEMBLY   Let's refer to the image of the blocking sensor below: The Connection of the Sensor to the Arduino is shown below: SENSOR  ----->       ARDUINO Signal   ...
Post a Comment
Read more

Arduino and Keyes KY-017 Mercury Tilt Sensor

HELLO THERE!!!     How are you guys? I hope everyone is fine and good as always. I am back in tinkering after a few months of hiatus( busy stuff :) ). So, today i would like to share with you guys on KY-017, which is a Keyes Mercury Tilt Sensor. KY-017 Sensor KY-017      The picture above shows the KY-017 Sensor from Keyes. It has 3 pins, A ground, A vcc, and A signal pin. If you look closely, there is a mercury ball inside the bulb like object. The mercury ball acts like a switch for this sensor. KY-017 Working Procedure: 1. When the sensor is not tilted, the mercury ball will be at the bottom of the bulb. This will complete the circuit and turns on the LED of the sensor. The output that is sent through the signal pin will be LOW. 2.When the sensor is tilted, the mercury ball will be at the top of the bulb(near at the sharper end). This will complete break circuit and turns off the LED of the sensor. The output that is sent through t...
Post a Comment
Read more